●性能範圍:Range of performance:

    1、最高工作壓力4.0MPa  1, the maximum working pressure of 4.0 MPa

    2、流量範圍 1～1000m3/h 2, 1 ~ 1000 m3 / h flow range

    3、溫度範圍-20～120℃  3-20 ~ 120 ℃, temperature range

    4、介質粘度 1～3000mm2/s，降低轉速可達到106mm2/s 介質粘度對雙螺杆泵性能影響較大，泵的名義排量💘是‼️指在特定粘度條件下的排量，為保證泵能在較高效率下工🍉作，在試驗✔️不充分時，建議按下列粘度條件👣選擇轉速：介質粘度cSt轉速r/min 　<4001500 < pan>　400 ～12001000 　1200～3600750。

    4, 1 ~ 3000 was/s, medium viscosity reducing speed can reach 106 was/s medium viscosity influence the performance of double screw pump, pump displacement refers to the specific viscosity of conditions in the name of the displacement, in order to ensure the pump can work in high efficiency, when the test is not sufficient, suggestion choice speed on the viscosity of the following terms and conditions: medium viscosity cSt speed r/min < 4001500 400 ~ 12001000, 1200 ~ 400.

    ●雙螺杆泵有密封式和不密封式兩種類型，按介質從一端還🔱是 從兩端進入齧合空間，雙螺杆又被分為雙吸式🐪和單📞吸式兩種結構。雙螺杆泵是外齧合🌈的螺杆泵，它利用相互齧合，互不接觸的兩根螺杆來抽送液體。雙螺杆泵為一種雙吸式非🚶密閉的雙螺杆泵。一端伸出泵外的主動螺杆由原動機驅動❗。主動螺杆與從動螺杆具有不同旋向的螺紋。螺杆與泵體緊密貼合。從動螺杆是通過同步齒輪由主動螺杆帶動的。Double screw pump has sealed and not enclosed two types, according to the medium from the side or from both ends into space meshing, double screw was divided into double suction type and structure of single suction type two kinds.Screw pump, twin screw pump is the external gear utilizing the mesh each other, mutual contact of two screw to pumping liquid.Double screw pump is a kind of double suction not airtight double screw pump.Active outside the side out of the pump screw driven by a prime mover.Driving screw and driven screw thread with different handedness.Screw pump body and tightly.Driven screw is driven by synchronous gear by the active screw.

    ●雙螺杆泵作為一種容積式泵，泵内吸入室應與排出室嚴密地隔開。因此，泵體與螺杆外圓表面及螺杆與🔞螺杆間隙應盡可能♌小些。同時螺杆與泵體、螺杆與螺杆間又相互形🧡成密封腔，保證密閉，否則就可能有液♌體從間隙中倒流回去。Double screw pump as a positive displacement pump, the pump suction chamber should be closely separated and discharge chamber inside.Therefore, the pump body and screw cylindrical surface and screw and screw clearance should be as small as possible.Screw pump body and at the same time, each other between the screw and screw and form a sealed chamber, ensure airtight, otherwise there may be liquid backflow from the gap.

    ●雙螺杆泵可分為内置軸承和外置軸承兩種形式。在内置軸承🌈的結構型式中軸承由輸送物進行潤滑。外置軸承結構的雙螺杆泵工作腔同軸承是分開的。由于這種🔴泵的結構和螺杆間存在的側間隙，它可以輸送非潤滑💔性介質。此外，調整同步齒輪使得螺杆不接觸，同時将輸出扭矩的一半傳給從動螺杆。正如所有螺杆泵一樣，外🧑🏾‍🤝‍🧑🏼置軸承式雙螺🔴杆泵也有自吸能力，而且多數泵輸送元件本身都是雙吸對稱布置，可消除軸向力，也有很大❌的吸高。Double screw pump can be divided into internal bearing and the outer bearing two forms.In the built-in bearing structure bearing lubrication by conveying material.Working with external bearing structure of the double screw pump bearings are separated.Owing to the pump structure and side clearance between screw, it can transport non-lubricative medium.In addition, the adjustment of the synchronous gear makes the screw does not contact, at the same time the output torque of the half to driven screw.Like all of the screw pump, external bearing type twin-screw pump, and most are double suction pump element itself symmetric arrangement, can eliminate the axial force, also has a lot of high absorption.

    ●雙螺杆泵系列産品分為單吸雙螺杆泵和雙吸雙螺杆泵兩大類。該系列産品具有特殊的螺杆型線和與之配套的特殊結構，廣泛适用于石油、化工、冶😍金、鋼鐵、電力、船舶、制藥、食品、建材等各種行業，其适用介質之多、輸送範圍之廣、應用工況之複雜是其🔴它泵類産品無法比拟的。這些特點也使得該系列泵具有潛在的使用發展前景。Double screw pump series products are divided into single suction of two kinds of double screw pump and double suction double screw pump.This series of products have special screw lines and form a complete set with the special structure, widely used in petroleum, chemical industry, metallurgy, steel, electricity, shipbuilding, pharmaceutical, food, building materials and other industries, by as much as its applicable medium, transmission range wide, application condition of the complex is unmatched by other pump product.These features also makes the use of this series of pumps with potential development prospects.

    ●泵體内裝有兩根左、有施單頭螺紋的螺杆，主動螺杆2由動力機驅動轉動時，靠同步齒輪1帶動從動螺杆3轉動。兩根螺杆以及螺杆與泵體. 之間存在着間隙，該間隙靠齒輪和軸承保證。其間隙大小，取決于液體粘度、工作壓力等因素。由于每根螺杆兩端螺紋的旋向相反，螺杆轉動時，由螺杆齧合線形成的泵工作腔。Equipped with two left in the pump body, a single thread screw, active screw driven by engine 2 turns, driven by synchronous gear 1 driven screw 3 rotation.Two screw and screw and pump body. There is a gap between the gap by gear and bearing.The gap size, depends on the liquid viscosity, pressure and other factors.Because each thread rotate to the opposite on both ends of the screw, the screw rotates, formed by the screw meshing line pump working chamber.

   ●該型泵采用雙吸式結構，螺杆兩端處于同一壓力腔中，軸向力可以自行平衡。兩端軸承采用外裝式㊙️，單獨✂️采用潤滑油(脂)潤滑，因而不受輸送介質的影響。兩螺杆間用一對同步齒輪驅💚動，螺杆齒面間并不接觸，而留有一微小間隙，介質中的雜質并不能對螺杆齒面産生直接的磨損(除沖刷外)。 除一些小排量泵外(2W.W4.0以下)，一般在泵體上都帶有内流式安全閥，當排放壓力超🌏過額定值時，有一定的保護作用。 泵體上的進出🆚口方向有兩種，一為🏒水平進，水平出;二為水平進，垂直向上出;用戶可根據自己需要選擇。This type pump adopts double suction type structure, at the same pressure in the cavity on both ends of the screw, the axial force can balance itself.Both ends of bearing mounted outside using, lubricated by lubricating oil (grease) separately, and therefore not affected by the medium.With a pair of synchronous gears drive between the two screw, the screw does not contact between tooth surfaces, and leave a small gap, the impurities in medium can not be directly on the screw tooth surface wear (except wash).Except a few small displacement pump (below 2 w. W4.0), generally contain flow relief valve on the pump body, when the discharge pressure exceeds rating, has certain protective effect.There are two kinds of the direction of the import and export on the pump body, one for level, level;Secondly, level, vertical;User can choose according to their own needs.

   ●雙螺杆泵如何進行日常維護與保養:daily maintenance and maintenance:

    1、每日的維護和保養1, daily maintenance and maintenance

    1.1在螺杆泵停泵時檢查齒輪箱（04）内的油位。若有必要，拆下注油螺塞（131），加油至油标（106）的中心處為止。1.2聽聽是否有異常噪聲與震動。1.3在泵運轉時檢查泵是否有洩漏。1.1 in the screw pump when the pump is going to check the oil level in the gear box (04).If necessary, disassembling bet on oil plug (131), go to the center of the oil standard (106).1.2 listen to whether there are abnormal noise and vibration.1.3 check for leaks pump when the pump is running.

    注意：對于機械密封，在大多數情況下，由于汽化導緻從密封洩☎️液孔處觀察不到洩漏，但有時少量而🔅又穩😄定的洩漏是允許的。Note: for mechanical seal, in most cases, due to evaporation from seal leakage of fluid leaking hole in observation, but sometimes a small amount and stable leakage is allowed.

    2、每周檢查與保養2, weekly inspection and maintenance

    2.1對于已經停止工作一周以上的泵，應打開進、出口🐕閥門🙇‍♀️，接通電動機電源，點動幾次泵。2.2檢查進、出口管道上的閥門是否可以工作正常。

2.1 for pump has stopped working for more than a week, should open the inlet and outlet valve, turn on the motor power supply, pump point move several times.2.2 check whether the valve in the inlet and outlet pipe can work normally.

    3、每季的維護與保養3, quarterly maintenance

    3.1檢查所有基礎上的螺母和壓緊裝置的螺栓是否💃🏻松動。3.2安裝規定每三月把齒輪箱的油更換一次。松開齒輪箱（04）的放洩螺塞（130），将齒輪油放掉。擰緊放洩螺塞，打開注油螺塞（131），注入清潔的輕油，清洗齒輪箱。清洗幹淨後打開放洩✊螺塞，放掉輕油，擰緊放洩螺塞，從注油螺塞口注入規♍定的齒輪油至油标（106）中間，擰緊注油螺塞。3.1 check all the nuts and bolts compaction device on the basis of whether is loose.3.2 installation regulations every march the gearbox oil replacement.Loosen the gear box (04) drain plug (130), put off the gear oil.Tighten the drain plug, open the oil plug (131), the injection of light oil cleaning, clean the gear box.Clean after playing open drain plug, release the light oil, tighten the drain plug, from the oil plug mouth into the provisions of the gear oil to oil standard (106), tighten the oil plug.

    4、每年的維護與保養4, the annual maintenance

    4.1檢查聯軸器的對中情況。4.2對照泵和電機的銘牌的數值，檢查泵的流量、壓力和功率❓的情況。如果有必要，在壓力和流量下降很多的情況下，則👣應對泵進行拆卸檢修，更換維修已損壞的部件。當然如果泵的性能仍然令人滿意，則🚩無需拆泵維修。4.1 check the coupling of the situation.4.2 the numerical control of the pump and motor nameplates, check the status of the flow, pressure and power of the pump.If necessary, in many cases fall in pressure and flow, should be made for the pump to remove the maintenance, replacement of repair damaged parts.Of course, if the performance of the pump is still unsatisfactory, you do not need to dismantle the pump maintenance.

    5、潤滑油系統油料更換時間5 oil, lubricating oil system change of time

    5.1軸承每月加入一次3#通用锂基潤滑脂。5.2齒輪箱新泵累計250小時更換美孚牌140或長城牌150車用齒輪油；連續運轉每1000小時，更換一次上述相同的車用齒輪油。5.3機械密封油：保證停機時油位在檢視孔中心，日常視情況補充，油品牌号：ISO VG22-150VG28(相當于20号機油)，每半年更換一次。5.1 bearing join once a month 3 # general lithium grease.5.2 new pump gear box has 250 hours to replace mobil card 140 or the Great Wall brand 150 vehicle gear oil;Every 1000 hours continuous operation, the replacement of the same vehicle gear oil at a time.5.3 mechanical seal oil: ensure that the oil level when the stop in the center of the peep hole, supplement daily circumstances, product brand: ISO vg28 VG22-150 (equivalent to 20 oil), replaced once every six months.